SEND EMAIL

e-ADMISSION

CONTACT US


 

SCIENTIFIC INTERNATIONALTRAINING INSTITUTE


SYLLABUS OF DIPLOMA/CERTIFICATE COURSE-

ELECTRICAL.

WIREMAN [ W ]

1. BASIC ELECTRICITY • Study of Voltage, Current and Resistance and their units (Kilo, Mega, Milli, Micro) • Study the meaning of circuit and know about close circuit, short circuit and open circuit. • Ohm's Law, Formula's and problem's on this law. • Study of series circuit, parallel circuit and compound circuit their formulas and solve simple problems. • Study about power their formulas and units. • Study about Electrical energy and Electric bill calculation. • Types of supply, polarity testing and effects of electric current. 2. TOOL'S Study about different type's of Tool's, required for electrical work. (wiring or repairing), their names, sizes, precautions to be taken while using different Tolls. • Types of Pillars ? Combination Pillar, Nose Pillar, side cutting pillar, Cert clip pillar etc. • Drilling Tool’s ? Rawal punch, center punch, chiesal, Hand drill, electric Drill, Gimlet etc. • Cutting Tools ? Hack saw, Hand saw, ordinary saw, Tenon saw, Scraper, Electrician knife etc. • Hammering Tools ? Ball pin hammer, Nail puller hammer, mallet etc. • Measuring tools ? Tape, Try square, sprit level, foot rule, S.W.G. etc. • Other tools ? Tester, screw driver, test lamp bearing puller, Blow lamp, spanners, files, soldering iron etc. 3. ELECTRICAL ACCESSORIES Study about various accessories use in wiring work their names, capacity and use. • Controlling accessories ? S. P. switch, two way switch, two way center of switch, Bell pust, Intermediate switch, I.C.D.P. and I.C.T.P. switch, Toggle switch etc. • Holding accessories ? Batten Holder, Angle Holder, Tube Holder, Starter Holder, Edison Screw type holder, pendent holder. • Accessories for safety ? Kit Kat fuse, Cut – Out, glass fuse, H.R.C. fuse, Cartridge fuse, MCB, ELCB etc. • Other accessories ? Two pin & Three pin plug, sockets, adaptors, ceiling rose, Gang box etc. 4. CONDUCTOR, SEMI CONDUCTORS AND INSULATOR'S WIRES AND CABLES • Study about conductor, semi conductor and Insulator's, their definitions and examples and use. • Study about construction of wire and cables their sizes and use's. • P.V.C. wire, C.T.S. wire, V.I.R. wire, flexible wire weather proof cable, enameled copper wire etc. • Armored and unarmored cable. 5. TYPES OF WIRING, EARTHING • Study about different types of wiring methods meaning of electrical points, layout drawing of flat wiring and how to prepare wiring work estimate. Precautions to be taken while doing wiring work, their advantages and disadvantages. • C.T.S. wiring, pipe wiring (P.V.C. and Heavy gauge), Casing capping wiring, consild wiring, Cleat wiring etc. • Study of earthing, types of earthing, testing of earthing, (pipe earthing and plate earthing) • Study of lightning Arrestor. 6. METER'S Study about different types of meters use commonly in electrical field, their construction, connection's, Capacity and precautions while using. • Voltmeter, Ammeter, Watt meter, Ohm meter. • Energy meter, • Meger meter etc. 7. JOINTS, SOLDERING, TAPPING • Why joints use in wiring work, types of Joints, precautions while make Joints. Simple twist Joint, 'T' Joint, straight Joint, western Union Joint, Britannia Joint. • Study about soldering methods, precaution while solder the Joints. • How Tapping is done after Joints. 8. OTHER • I.S.I. Symbols, Safety Rules, Study about Various Long Forms.Tube light ? Construction, parts, connection, faults and testing., Ceiling fan ? Construction, Parts, Connection, faults and testing. • Series parallel testing board., Electric Bell’s


ELECTRICIAN [ E ] [ E / DEES (EL) I / ADEES (EL) I ]

1. BASIC ELECTRICITY • Study of voltage, current, Resistance their units. • Close circuit, open circuit, short circuit • Ohm's Law • Series, Parallel and combine circuit. • Power, power factor, Electrical Energy Bill calculation. • Types of supply A.C. (1ph, 3ph, 3ph and N), D. C. Supply. 2. ELECTRICAL APPLIANCES • Study about various appliances use in house hold purpose, their construction, working, faults and reasons, testing, precaution when using them. • 1. Electric Iron (ordinary and automatic) 2. Toster 3. Soldering Iron 4. Storage type Heater 5. Immersion type water heater 6. Table fan 7. Mixer 8. Food processor 9. Washing machine 10. Exhaust fan 11. Ceiling fan 12. OVEN. 3. CELL'S AND BATTERIES • To study of electrolysis, electro light and electroplating. • Study of primary cells and secondary cell, and their difference, study of following primary cell. • Primary cells Voltaic cxell, Donial cell, Dry cell. • How to find out Internal resistance of cell. • Secondary cell study about lead acid batteries, their construction, chemical reaction when charging and discharging time, precautions while using batteries. • Faults produce in batteries. • Capacity of battery • Charging methods of battery, constant current and constant voltage method. • Indications of charge battery. • Know about Hydro meter and High rate cell discharge cell Tester. 4. MAGNET AND MAGNETISM • Definition of magnet, their properties • Types of magnet (Natural and artificial) • Weber’s molecular theory • Methods of prepare magnet in Lab • Study of electromagnet. • To study of definition relating to magnet Like ? Magnetic pole, mag.Lines, mag.field, polar Axis Unit Pole, Mag.Induction etc. • Some definition relating to electro magnet. Lime ? M.M.F., Reluctance, Ampere turn etc. • Study about various laws relating to magnet and electromagnet. • Right hand rule, cork screw rule, Fleming right and left hand rule, Lenz’s law, Faraday’s law of electromagnetic induction, end rule • Self induction • Mutual induction. 5. D. C. GENERATOR • Definition of generator • Working Principal of Generator • Difference between A.C. and D.C. Generator • Study about parts of D.C. Generator Like ? Yoke, pole core pole shoe, field winding Armature, Brush, Front and end plate, Bearings. • Types of D.C. Generator based on connection between armature and field winding 1. Series Gen. 2) Shunt Gen. 3) Compound Gen. • Study of E.M.F. formula of D.C. Generator. • Losses (Mechanical and Electrical), and faults produce in D.C. Generator. • Armature reaction • Interpol 6. TRANSFORMER • Introduction of Transformer • Working Principle of Transformer • Main parts of Transformer • Various Types of Transformer 1. Core type Tx. 2) Shell type Tx. 3) Berry type Tx. 4) Step up Tx. 5) Step Down Tx. 6) Current Tx. 7) Potential Tx. 8) Distribution Tx. 9) Auto Tx. • Study about Transformer ration. • Study about cooling methods of Transformer 7. A. C. MOTOR (1ph & 3ph), STARTER'S • Definition of motor • Difference between AC and D.C. Motor • Working principle of 3ph and 1ph motor's • To study various parts of AC motor, like yoke, stator, Rotor, winding, centrifugal switch, bearings, front and end plate, name. • Study about various single phase Motor's split phase motor, capacitor motor (C.S.C.R., Cap. start Induction motor, permanent capacitor motor) • Shaded pole motor • Universal motor. • Study about various Three phase motors • 3 ph squirrel cage Induction motor. • Slip ring Induction motor. • Synchronous motor. • Faults and their reasons produce in AC motor's • Motor's and their applications. • Starter required for 3 phase motors DOL Starter, Semi and Automatic star Delta Starter, Reverse forward switch. 8. ILLUMINATION • To Study generation of light and study in brief radiant energy. • To study various definition relating to illumination • Study of different methods of illumination, direct method, indirect method, semi direct and semi indirect method. • Study of different types of lamps. Incandescent lamp, Arc lamp, Gas Discharge Lamp (Mercury Vapour lamp, sodium vapour lamp, Neon Lamp etc.) 9. CONDENSER (CAPACITOR) • Study about the definition of condenser, and study of construction of capacitor. • Various definition related to capacitor for ex. Capacitance, capacitive reactance. • Study of series and parallel connection of capacitor • Study of various types of capacitors, their use in electrical field • Testing of capacitor 10. MEASURING INSTRUMENTS • Study of various types of meters • 1) Indicating meter's 2) Integrating meters 3) Recording meter's. • Parts of meters • Precautions to be taken while using meters. • Connections of various meters. 11. GENERATION, TRANSMISSION, DISTRIBUTION • Study about different types of Generation system of electricity, Study of sources from which electricity is produced, Primary source solar energy, Secondary source Thermal power station, Hydro electric power station, Diesel power station, Study of Insulating material use in over head wiring.,Poles use in over head wiring, Know about over head wiring Earthing pit.,Study about under ground caballing, Cable's used in under ground wiring. • Study about distribution of electricity (L.V.),


ARMATURE MOTOR REWINDING [ MW ] [ MW / DEES ( EL) II / ADEES ( EL ) II ]

1. BASIC ELECTRICITY • Study of voltage, current , resistance and their units • Ohm's Law • Series and Parallel circuit and their properties with respect to winding • Types of Loads Inductive, Resistive, Capacitive • Power, Power factor, Disadvantages due to low power factor. • Methods of improve P. F. by using capacitor Bank. • To study types of supply. 2. TOOLS, AND WIRES WINDING MATERIAL, VARNISHING • Study of tools required for winding and study of their application. Types of plier, Types of Saw, Types of hammers, Special Tools required for winding work like Blow lamp, seasor, center punch, Bearing puller, wire pusher, Coil spreader, soldering iron etc. • Study of various types of insulating materials with respect to insulation class an temperature. • Insulating paper, sleeves, Tapes, wedges, varnish, Thread's etc. • Study about winding wires Enameled copper wire. • Varnishing Dipping and Brushing. • Study reason of varnishing, method's of varnishing. • Pretest before taking up winding for varnishing. 3. SPECIAL INSTRUMENTS REQUIRED IN WINDING AND METERS • Special instrument required for winding work • To measure gauge of conductor S.W.G. • To measure diameter of conductor micro meter. • For testing of motor's series parallel testing board • For armature testing Growler. • Meters used in winding work Voltmeter, Ammeter, Wattmeter, Multi meter, Oho Meter, Clamp tester, Digital etc. 4. MAGNET AND MAGNETISM • Study about magnet, Properties and types of magnet. • Study of electro magnet. • Definitions related to magnet Like magnetic pole magnetic field, magnetic lines, polar Axis, magnetic induction. • To study various laws related to electro magnet, Right hand rule, cork screw Rule, Fleming's right and left hand rule, faradays law of electro magnetic induction. • Self induction and mutual induction. 5. D. C. MOTORS • Definition of motor, it's application, Types of motors A.C. and D.C. • Main parts of D. C. Motors yoke, pole core, pole snoe, field coil, Armature, brush, bearing, front & End plate. • Working of D. C. Motor • Types of D. C. motor series, shunt and compound motor • Types of slot's make of starter, Armature and rotor Open type slot, Semi close slot, close type slot. • How to start D. C. shunt motor. • Losses and faults produces in D. C. motor. • Armature reaction • Inter pole. 6. TRANSFORMER, ALTERNATOR • Definition, working principle of Transformer • Main parts of Transformer • Step up and HT Transformer. • Transformer Ratio • Cooling method's of Transformer. • Current Transformer (CT) and Potential Transformer (PT) • Study of alternator, definition and working principal of Alternator. • Various terms used with reference to AC supply for ex Alternating current, cycle, frequency, Time period, peak value, R.M.S. value. • Study of star Delta connection • Know about poly phase. 7. A. C. MOTORS 91 PH, 3 PH) AND STARTERS • Definition of motor • Working principal of 3 ph and 1 ph motor's • To study various parts of A. C. motor • Study about various single phase motors • Split phase motor's • Capacitors motor's • Shaded pole motor • Universal motor. • Study about various Three phase motors. • 3 ph squirrel cage induction motor • Slip ring Induction motor • Faults and their reasons produce in A. C. Motors • Testing of Motor • Motor's and their applications • Starters required for 3 phase motors D.O.L. starter, Semi and Automatic star Delta starter R/F switch, Auto transformer starter. 8. CAPACITOR • Study the construction of capacitor • Some definition relating to capacitor Like Capacitance, capacitive Reactance. • Series parallel connections of capacitor • Testing of capacitor • Use of capacitor in electrical field. 9. WINDING TERMS • Study of various forms used in winding like Coil pitch, Coil span, Pole pitch, front pitch back pitch. • Know about Armature winding. • Lap and wave winding • Progressive and retrogressive winding • Single, Double and Triple layer winding • Study about how prepare Data and diagram of Armature winding • Balancing of armature. • Study of 1 ph stator winding Data / Drawing and which points to be noted when the done winding work. • Study of 3 ph stator winding Data / Drawing and which points to be noted when the done winding work. • Various definition related to winding like Coil, coil side, coil led, Tapping, Coil Group per phase coil, Layer and Double Layer winding in 3 ph motor. (Winding Drawing list same as give in practical list)

( DEES – ( EL ) PAPER – III ) 1. I.S.I. SYMBOL’S, I. E. RULES • Know about meaning of I.S.I., I.S., I.E., I.S.O. etc. • Study of different symbol's use in Electrical Drawing (More than wireman levea) (150 To 175 symbols) • Study of different I. E. Rule related to electric supply company, H.V., L.V. consumer's House wiring, Industrial Installation, cinema Hall's etc. 2. POWER GENERATION SYSTEMS, TRANSMISSION DISTRIBUTION • Study about various types of power station's their Drawing's, block diagram, capacity of various power station's • Their advantages and disadvantages • Thermal power station's. • Hydro Electric power station's, • Atomic power station's. • Gas turbine power station's. • DIESEL Power station's • Windmill plant • Solar energy plant. • Study about Transmission systems • Why Transmission is high, study about Transmission voltages • Like 11kv, 22kv, 33kv, 66kv, 132kv etc. • Study different poles and lowers use in Transmission line's their Drawing • Study about O.H. and under ground wiring • Types of garding use for OH lines. • Various definition related to above like main feeder, Transmission feeder, Distribution lines, service mains etc. • Layout Drawing of Transmission, Distribution • Study about various Electrical Distribution system REDIAL DISTRIBUTION, RING DISTRIBUTION, Their Drawing Grid Distribution. • Tree Distribution. 3. SUB STAION • What is sub station ? Importance of substation in Transmission and Distribution system. • Equipment use in sub stations, their names and use is sub station For ex Transformer, C. B., Isolator, Fuse, Lightning Arrestor, metering panel etc. • Work of Sub Station. • Types of substations like 1. Transformer substation a) step up Sub Station's b) Step Down Sub Station's 2. Secondary sub Station's 3. Distribution sub Station's 4. Switching sub Station's 5. Power factor correction sub Station's 6. Converting sub. Station's 7. Industrial sub station 8. Indoor sub station's 9. Out Door sub station's 10. Pole minted sub station's(2 pole, 4 pole structure) 11. Plinth mounted sub station's 12. Under Ground sub station's • Various Drawing's of sub stations • Single line Diagram of 11 kv Indoor sub station's. 4. SUB STATION EARTHING, LIGHTNING ARRESTOR • Why earthing need in sub stations, Methods of prepare earthing, Testing of earthing , Study about need of Double earthing for Industrial or Substation equipments, Know about lightning Arrestor, working of this • And types of lightning arrestor of ex, Horn gap lightning arrestor, Oxcide film arrestor, Auto valve arrestor • Thyrite Arrestor, Electrolytic Arrestor. Use of Ground conductor for H. T. Lines. 5. H. T. Transformer • Working of Transformer. • Study about H. T. Transformer's Power TX and Distribution TX. • C.T. & P.T. • Difference between then • Parts of above TX. • Efficiency of TX. • Various testing of TX. • Parallel connections of two TX. • Maintenance of TX. Daily, weekly, Monthly, ½ yearly, yearly, after five years. • Oil Testing. 6. A) BUSBAR B) CAPACITOR INSTALATION A) BUSBAR • Study about Bus bar, Metals use of bus bar's, Bus bar Reating, Method's of Bus bar connection's use in various place's, Single Bus bar method, Duplicate bus bar method, Sectional bus bar method,Know about Lug's and Crimping Tool's. B) Use of capacitor in industrial installation. Study about power factor, losses of low P. F. How improve low P. F. with the help of capacitor bank, Testing of capacitor. 7. A) ISOLATER AND CIRCUIT BREAKER'S, INDUSTRIAL WIRING A) Know difference between switch, Isolator and circuit breaker's • Drawing of Isolator • Study about different types of C.B. their use, capacity, Connections etc. Study about M.C.B., ELCB, Minimum oil C.B., Vacuum C.B., SF6 CB, Air blast C.B. etc. B)Study about Industrial wiring, sample layout Drawing of Industrial wiring. • Materials use for above wiring like Cables, S. F. unit's, clamps, I.C.D.P., I.C.T.P. switches, Distribution Boxes. • Precaution's while Install Industrial wiring. 8. A) LIFT INSTALLATION B) PANEL BOARD WIRING • Why lift's are mostly use in recent days. • Construction of lift • Parts of Lift's installation like lift well, Guide Rail, Counter weight, Lift car, car Buffers, counter weight buffers, Gear's, Motor, rope Indicators, safety gears, • Know about machine room • Safety equipment use in Life installation. Slack rope switch, Terminal slow down switch, Terminal stopping switch, over speed governor. • Various types of Lifts. Passenger Lift, Goods Lift, Service Lift, Faire Lift, Hospital Lift etc. • Rules related to Lift Installation. B) Know about panel Board, which types of work include for make panel Board, Like-Layout of panel Board. • Connection Drawing of panel Board, Fabrication work, Electrical fitting work etc, Two three Drawing of panel Board, Front view, connection Drawing, Precaution to be taken when making panel Board. 9. A) SUPPLY POINTS B) WATER PUMP INSTALLATION C) FIRE RIGHTING INSTALLATION D) FARM HOUSE WIRING A) Supply Points.Know about meter room wiring for chawl types rooms, 2 3 Floor's Building's, Towers etc. Industrial supply. Know about which documents are necessary for new meter connection. B) Water Pump Installation-Know about water pumps Installation's, precautions, while Installing pump. C) Know about fire fighting Installation. D) Know about farm house wiring, Precaution when done this work. 10. A) STAND BY POWER SUPPLY B) WASHING MACHINE A) Stand by Power Supply- • Need of stand by Power supply, Sources of stand by power supply, Diesel Generator set, Inverter, wiring, methods of Inverter's, U.P.S.,Wash B) Washing Machine • Construction of machine, Parts of Machine, faults produce in Washing Machine Testing.


 

SCIENTIFIC INTERNATIONALTRAINING INSTITUTE SYLLABUS OF DIPLOMA/CERTIFICATE COURSE- MECHANICAL

TURNER ( T )

1. SAFETY: General safety, Personal safety, Mechanical tool safety, Safety rules to be observed in Workshop. First-Aid knowledge & cause of accident & its prevention. 2. UNITS OF MEASUREMENTS: British & Metric system of units, its conversions in respect of measurements for e.q. linear, Area & volume. 3. MEASURING INSTRUMENTS: i) Classification of measuring Instruments. ii) Precision Instruments: - Micrometer (Out side, inside, depth gauge) Calipers: Vernier Caliper, Height Gauge, steel rule, Try square slip gauge, sine bar. iii) Non-precision Instruments: Steel rule.Caliper: Outside, Odd leg divider, Combination set, try square Marking tools: Scriber & Scribing block, Surface plate, punches, hammers, Angle plate, Vee block, Marking Media (Persian Blue, Red Lead, Chalk). 4. CUTTING TOOLS: i) Study of different cutting tools such as chisels, hacksaw blade. ii) Files: Description, its material, grades, cuts & its parts uses. Specification. Care & Maintenance of files File cards, pining of files, Special types of files such as needle files, Safe edge files, hand file etc. iii) Cutting tools, its uses & selection of special tools such as drill, reamers, grinding wheels, knowledge of re sharpening of these tools. iv) Drill: Knowledge of standard drill sizes such as letter No. & fractional drill nomenclature of drill & important angle of drill, causes of breakage of drill. Importance of cutting speed and feed for drilling. v) Use of Tap and Die Material for Tap & Die safety precautions while tapping. 5. HOLDING DEVICE: i) Work Holding Devices: Construction & use of devices such as bench vice, Machine vice, Clamps, Parallel block, step block, Nuts & Bolts etc. ii) Cutting tools holding Device: Knowledge of holding devices such as sockets, Sleeves, Drill chucks, die stock & Top range. 6. GENERAL HAND TOOLS:Knowledge and importance of workshop, hand tools such as screw driver, Spanners, Single ended, ring spanner,pliers, mallet, soft hammer etc. 7. ENGINEERING FASTNER:Types of standard threads, such as metric BSW, BSP,BA, square, knuckle, ACME Threads and their applications.Types of screw such as counter sunk, Hexagonal, square half round headed screw,Alenkey. Importance of fasteners in workshop practice, permanent fastener such as rivets, welding, Soldering, brazing, types and method of riveting. Temporary fastener: Various types of keys, pins, and cotters nuts and bolts. Studs, Washers etc. 8. LUBRICATION & LUBRICATIONS: i) Importance of coolants & Lubrication in workshop. ii) Properties of Lubricants, coolants for various metals. iii) Types of coolants, Lubricants used for machines. iv) Preventive Maintenance necessity. Advantages & Types of maintenance. 9. LIMITS, FITS, TOLERANCE & INTERCHANGEABILITY: Standard systems of limits, fits & tolerance as per Indian standard, concept of Interchangeability. 10. JIGS & FIXTURES: Construction & necessity of jigs & fixture, principles & Material used for Jigs & fixtures. 11. LATHE MACHINE:i) Function &Familiarization with lathe machine.and safety while working on it. 12. LATHE MACHINES SPECIFICATIONS: i)Lathe machine main parts such as head stock, Tall stock, Carriage feed screw and lead screw. Lathe machine driving mechanism Gear driving and belt driving. Use of back gear. 13. TYPES OF LATHE MACHINES:Understand different types of lathe machines such as center Lathe, Bench Lathe, Capstan Lathe and turret Lathe, special lathe (Gap Bed Lathe). 14. LATHE MACHINE ACCESSORIES AND ATTACHMENTS:Study of the Lathe accessories such as Centers, Carrier Catch plate, Chuck face plates, Collate, Driving plate, Mandrel and tool post etc. 15. LATHE OPERATIONS:Understand basic common lathe operations such as facing, plain turning, centering, step Turning, shoulder turning, grooving, chamfering, boring etc. ii) Special Lathe Operations: Taper Turning, Use of Taper, Methods of calculation and Formulas. 16. INTRODUCTION TO C.N.C:i) Operations of C.N.C. machines.ii)Fundamental components and its function.. iv) a)Point to point control b) Continues path control. v) Types of N.C. system and its function. a) Open loop b) Closed loop. vi) Brief knowledge of binary arithmetic.1. Advantage of C. N. C

FITTER ( F ) [ FITTER / DMES I / ADMES I / DPES - I ]

1. SAFETY: General safety, Personal safety, Mechanical tool safety, Safety rules to be observed in Workshop. First-Aid knowledge & cause of accident & its prevention. 2. UNITS OF MEASUREMENTS: British & Metric system of units, its conversions in respect of measurements for e.q. linear, Area & volume. 3. MEASURING INSTRUMENTS: i) Classification of measuring Instruments. ii) Precision Instruments: - Micrometer (Out side, inside, depth gauge) Calipers: Vernier Caliper, Height Gauge, steel rule, Try square slip gauge, sine bar. iii) Non-precision Instruments: Steel rule. Caliper: Outside, Odd leg divider, Combination set, try square Marking tools: Scriber & Scribing block, Surface plate, punches, hammers, Angle plate, Vee block, Marking Media (Persian Blue, Red Lead, Chalk). 4. CUTTING TOOLS: i) Study of different cutting tools such as chisels, hacksaw blade. ii) Files: Description, its material, grades, cuts & its parts uses. Specification. Care & Maintenance of files File cards, pining of files, Special types of files such as needle files, safe edge files, hand file etc. iii) Cutting tools, its uses & selection of special tools such as drill, reamers, grinding wheels, knowledge of re sharpening of these tools. iv) Drill: Knowledge of standard drill sizes such as letter No. & fractional drill nomenclature of drill & important angle of drill, causes of breakage of drill. Importance of cutting speed and feed for drilling. v) Use of Tap and Die Material for Tap & Die safety precautions while tapping. 5. HOLDING DEVICE: i) Work Holding Devices: Construction & use of devices such as bench vice, Machine vice, clamps, Parallel block, step block, Nuts & Bolts etc . ii) Cutting tools holding Device: Knowledge of holding devices such as sockets, Sleeves, drill chucks, die stock & Top range. 6. GENERAL HAND TOOLS: Knowledge and importance of workshop, hand tools such as screw driver, Spanners, Single ended, ring spanner, pliers, mallet, soft hammer etc. 7. ENGINEERING FASTNER: ( Types of standard threads, such as metric BSW, BSP,BA, square, knuckle, ACME Threads and their applications. ( Types of screw such as counter sunk, Hexagonal, square half round headed screw, Alenkey. ( Importance of fasteners in workshop practice, permanent fastener such as rivets, welding, Soldering, brazing, types and method of riveting. ( Temporary fastener: Various types of keys, pins, cotters nuts and bolts. Studs, Washers etc. 8. LUBRICATION & LUBRICATIONS: i) Importance of coolants & Lubrication in workshop. ii) Properties of Lubricants, coolants for various metals. iii) Types of coolants, Lubricants used for machines. iv) Preventive Maintenance necessity. Advantages & Types of maintenance. 9. LIMITS, FITS, TOLERANCE & INTERCHANGEABILITY: Standard systems of limits, fits & tolerance as per Indian standard, concept of interchangeability. 10. JIGS & FIXTURES:Construction & necessity of jigs & fixture, principles of jigs & fixture, Material used for Jigs & fixtures. 11. GAUGES:Knowledge of standard gauges. Classification of gauges such as working gauges, Inspection gauges and Master gauges. Types of Gauges such as snap gauges. Thickness gauges, wire gauge, plug gauges etc. 12. BEARINGS: Introduction & classification of bearings. (general & thrust) Types of bearings such as Roller, Taper roller bearings ball bearings, needle roller bearing, Importance of bearing in Machine tools. 13. BASIC ELECTRICITY: Basic terminology's in Electricity, Ohm's law & it's applications, Conductors & Insulators Principles of transformers.


[ DMES - II / ADMES - II ] WORKSHOP TECHNOLOGY II

1. MACHINES : A. LATHES 1. Different types of lathe machine a. Turret, b. Capstan, c. Automatic d. Semi automatic. 2. Identification & functions of lathe machines. 3. Speed and feed change arrangements 4. Different operations performed on lathe machine. B. MILLING MACHINE 1. Different types of milling machines. 2. Elements of milling machines. 3. Milling cutter (a) Related terms (b) Classifications. 4. Indexing, indexing method and its calculations 5. Different operations performed on milling machine. C. SHAPING MACHINE 1. Identification and function, main features 2. Explanation quick return motion and stroke setting 3. Clapper box and tool 4. Machining methods for horizontal, vertical and inline surfaces. 5. Method of setting up work. D. GRINDING MACHINE : 1. Standard types of grinding machines and their use. 2. The abrasive wheel 3. Simple consideration of cutting action. 4. Choice of wheel. 5. Wheel balancing and dressing E. DRILLING MACHINE 1. Different types of drilling machines 2. Types of drills and its materials 3. Drilling operations 4. Tool and work holding devices F. C.N.C. MACHINES 1. Operations of C.N.C. machines 2. Fundamental components and its function 3. Types of N. C. 4. (a) Point to point control (b) Continues path control 5. Types of N.C. system and its function a) Open loop b) Closed loop 6. Brief knowledge of binary arithmetic 7. Advantage of C.N.C. 2. WORKSHOP LAY OUT : 1. Types of building in which plant is installed. 2. Method of mounting and aligning machine on beds. 3. Test to be required after erection of machine in shop. 4. Products layout and process lay out. 3. SURFACE FINISHING PROCESS & COATING : 1.Necessity of surface finish. 2. Advantage of surface finish.3.Methods of surface finishing such as grinding, lapping, honing, buffing Super finishing etc.4.Advantages of coating. 5.Method of surface preparation, Metal spraying. 6. Method of coating such as galvanizing, electroplating, Zinc plating, Powder coating, anodizing, hot dipping.7.Advantages of painting.8.Method of painting. 4. MACHINING PROCESS : Subtraction, Addition, Non-subtraction, Non-Addition, machining such as shaping, slotting, milling, drilling etc. Addition process : Such as welding, brazing, soldering, plating etc. Non-subtraction, Non-addition processes : Bending, Twisting, Forging, Shearing, pressing etc. 5. HEAT TREATMENT : 1. Necessity & purpose of heat treatment 2. Advantage of heat treatment 3. Method of heat treatment : Annealing, Normalising, Hardening, Tempering case hardening. 6. MATERIAL HANDLING, CONVEYING & STORING SYSTEM General terms loading, unloading shifting, various equipment's used for shifting loads. Eq. Crow bar, Lever, Magnetic blocks, Rope, Pulley, Hoist, Jacks, Cranes, Fork lift, Conveyers belts, winch etc. Various storing systems used for solids liquids & gaseous materials classification & storing materials safety precautions. 7. MAINTENANCE ACTIVITIES Maintenance definition, Different types of maintenance preventive maintenance, Aim & Basic activity, Break down maintenance. Planning of maintenance schedule Maintenance of machinery's & material handling equipment's.


[ MD - II / DMES III / ADMES III / DPDD I / DPES II ] 1. INTRODUCTION OF DRAWING :- Use of different drawing instrument, single stroke lettering, Gothic lettering. Types of lines. Dimensioning techniques viz:- Aligned system and Unidirectional system 2. GEOMETRICAL CONSTRUCTIONS :- Simple geometrical construction such as bisecting a line, arc, perpendicular line, parallel line, dividing a line etc. construction of regular polygon by any one method. Internal and external tangent to a circle, machine handle. 3. SCALE :- Types of scale, representative fraction (R.F.). Classification of scale i.e. plain scale, Diagonal scale and problems on it, conversions. 4. ENGG. CURVES :- Construction of ellipse by arc of circle method, rectangle method, oblong method, Parabola by rectangle method, hyperbola, Cycloid, epicycloid hypocycloid, Involutes etc. 5. PROJECTION OF POINT/LINE/PLANES a) Projection of point in four quadrant. b) Projection of Lines inclined to one surface plane only and lines in one quadrant. c) Projections of planes circular, square, rectangular, pentagonal and hexagonal shapes, inclined to one reference plane. 6. ORTHOGRAPHIC PROJECTIONS : First Angle and third Angle projection methods, Drawing orthographic from pictorial view of object. 7. ISOMETRIC PROJECTIONS :- Isometric scale construction. Drawing isometric views from orthographic projections 8. SECTIONAL VIEWS :- Types of sections like full section, half section, offset sections etc. Interpretation of views i.e. Missing views 9. FREEHAND SKATCHES :- Application of nuts, bolls, rivets, rivetted joint. Screw threads, split pins, keys, couplings etc. 10 ASSEMBLY DRAWING :- Study the drawings of component of assembly and their relative position in the assembly Assemble the parts and prepare orthographic drawing such as elevation plan, side view inclusive of section and half section views. Prepare the bill of materials.


DMES - IV / ADMES - IV ] SECTION-1 (60 MARKS) WORKSHOP MANAGEMENT 1. Principle of supervision 2. Quality Control / Inspection 3. Bill of Material / Estimation 4. Job Planning 5. Basic knowledge of factory act, standard orders, ESI and provident fund act, Factory act etc. 6. Knowledge of Industrial safety accident prevention and investigation of accident 7. Concept of quality circle. 8. ISO 9000 9. Customer service 10. Basic knowledge of tool CRIB and STORES 11. Purchasing 12. Time keeping 13. Minimum wages Act / payment of wages Act. 14. Selection of persons for jobs. 15. Decision Making 16. Job Allocation 17. Selection of workman 18. Knowledge of Apprentices Act 1961. 19. Knowledge of First Aid and First Aid box 20. Execution of power 21. Incentive Scheme 22. Time study, Method study and work study work simplification. 23. Costing of job 24. Knowledge of labour Control. 25. Communication skill SECTION II ( 40 Marks ) WORKSHOP CALCULATION 1. UNITS & MEASUREMENT : Definition of unit. Types of units. Systems of units. Conversion of units of simple Quantities form one system to other. 2. SIMPLE ARITHMETIC : Definitions, Simplification, Equation, Simplification of equation. Simplification of simultaneous equation. 3. MENSURATION : Definition, Plain figures, Areas of simple figures, Area of polygon. Calculation of volume of solids such as Cylinder, Ring, Pyramid, Prism, Frustum of a cone. 4. WORK POWER ENERGY : Definition of work, power & energy, Types of energies. Horse power, Definition, Types, Transmission of power by Belt pulley drive, Mechanical advantage, Velocity ratio & Efficiency. 5. CUTTING SPEED & FEED : Definition, Factors affecting cutting speed, Cutting speed calculation for lathe, shaper & drill machine, simple calculation. 6. TAPER TURNING : Taper turning method. Taper calculation for 1. Tail stock offsetting method. 2. Uniform compound rest method. 3. Taper attachment method. 7. BILL OF MATERIAL : Bill of material for simple mechanical assembly, consisting of seven to eight items.

 

WELDER PRACTICE ( WP )

ARC WELDING 1. Importance of safety, causes of accidents General safety precautions work shop safety, self safety and Machine safety. Arc welding safety precautions to be taken while connection and operating of welding machine. 2. Tools and equipment's require for arc welding. Basic hand tools Fields, Hammer, Chisel try square calipers and their uses. Basic measuring tools Scale & tapes measurements in metric & British units. 3. Arc welding terms and definitions. 4. Basic electricity A.C. & D.C. Electrical terms current, voltage watt, resistance etc. 5. Different metal joining processes :- Mechanical Riveting, Bolting, Hooking. Thermal Soldering, Brazing, Forging, Welding. Types of joint and their edge preparation. Distortion, their causes and method to overcome it. Arc length short etc. long arc, Advantages and disadvantages of each. Arc welding it's principles carbon and metallic arc. Different types of electrode and their flux coating. Welding positions Down hand, horizontal, vertical and over head. Arc welding machine Transformers, Generators, rectifier their construction, uses, advantages and disadvantages of each other. Welding symbol's for various joints. Welding of ferrous metals, mild steel, cast iron, stainless steel. Welding of non ferrous metal brass, copper, aluminum. 6. Defect in arc welding their causes & correction. Testing of weld various non destructive tests and destructive tests. Resistance welding spot, butt, seam, Projection welding Advance welding techniques, Argon arc welding. Co2 welding, submerged welding.

2. GAS WELDING 1. Safety precautions for gas welding. Safety precautions to be taken for cylinders, regulators while handling the gas welding plant. 2. Gas welding tools and equipment's and it's uses. 3. Common fuel gases used in welding i.e. Hydrogen, Coal gas, Propane and acetylene. 4. Types of various flames and their uses. 5. Types of joints and their preparations. 6. Gas welding torches, their types, uses and construction. Introduction to high pressure and low pressure gas welding plants Advantages & disadvantages. Purifier and hydraulic Back pressure value. Welding techniques, left ward and right ward techniques. Different ferrous metals welding by gas i.e. mild steel, cast iron, stainless steel, Different non ferrous metal welding by gas i.e. Brass, Copper, Aluminum. Brazing of mild steel copper cast iron. Soldering methods & their uses.

3. GAS CUTTING Principle of oxy Acetylene cutting. Cutting torch and it's construction. Oxy Acetylene cutting procedure straight, angular and circle cutting. Machine cutting processes Trolley, cutting, Profile cutting, Powder cutting.

 


AUTO ELECTRICIAN (ATE)

1. SAFETY Safety precautions to be observed in Auto Electrical Department. 2. TOOLS, EQUIPMENTS, MEASURING INSTRUMENTS [CHECKING INSTRUMENTS] General Hand tools, soldering materials and method of soldering, standard wire gauge, micrometer, ohmmeter, Ampere meter, voltmeter, meggar, multimeter and their use, Growler Armature Tester. Battery charger. 3. ELECTRICAL TECHNICAL TERMS AND BASIC ELECTRICITY Conductor, Insulator, Resistance current, volt, Power energy, circuit and their types, ohm's law, Potential difference, fuse Terminal their definations and unit. Simple problem on ohm's law and power. 4. MAGNETISM Terms used, type and shapes of magnets and properties methods of magnetizing and magnet materials, Electromagnet and advantages. Principle of magnetism, cork screw and R. H. Thumb rule - Magnetic field of current carrying conductor and loop Residual magnetism solenoid and it's polarity, palm rule etc. 5. BATTRIES Types of batteries, work of Battery on Automobile vehicle, Battery construction, Battery checking method hydrometer and H.R.D. Battery charging method. Distinguish between lead acid Battery and Alkaline Battery, effect on battery by under charging and overcharging, Trouble shooting of Battery. 6. DYNAMO AND REGULATOR Dynamo principle, Faraday's law of Electromagnetic Induction. Dynamo construction and it's ports checking procedure. Dynamo working, Types of dynamo, Third brush dynamo, Regulator circuit diagram. Types of regulator it's construction and working, Regulator setting procedure. Trouble shooting. 7. ALTERNATOR Principle of alternator. Main difference between alternator and dynamo. Alternator construction it's parts making and checking procedure. Alternator working, Voltage Regulator. Types of Regulator. Alternator wiring and charging circuit diagram, Working of Battery Indicator light. Maintenance and trouble shooting. 8. ENGINE STARTER MOTOR Use of starter motor, principle of starter motor. Types of starter motor by field and carbon brush. In board drive mechanism and out board drive mechanism. Types of starter motor solenoid switch, starter. Motor test. Trouble shooting and maintenance. 9. IGNITION SYSTEM Function of Ignition system. Types of Ignition system. Parts of Ignition system Ignition coil, Condenser distributor, advance mechanism. Spark plug their construction and working. Types of spark plug hot and cold plug. Spark plug specification Trouble shooting and maintenance of Ignition system and spark plug. 10. AUTOMOBILE WIRING AND DASH BOARD INSTRUMENTS Advantages of 12v battery. Earth Return system. Types of wire and wire terminal, wiring horness, precaution to be taken while wiring. Automotive electrical bulbs, Types of switches, use of fues, wire colour code system. Circuit diagram of head light, side Indicator light Tail light, Brake light, Reverse light etc. Electric Horn and Horn, circuit. Wind screen wiper motor, electrical fuel pump. Heater plug. Fuel gauge, Temperature gauge. Wiring diagram of center locking, Remote locking & power windows systems.

 


DIESEL VEHICLE MECHANIC ( DVM ) 1. SAFETY Safety precaution to be observed in workshop / motor garage. Tools and Equipment : Hand Tools and equipment for performance measurement in Automobile Trade. 2. MOTER VEHICLE INDUSTRY- General idea of motor vehicle. Motor vehicle manufacturer in India. Indian Automobile and Accessories manufacturer. 3. ENGINE- General description of internal combustion engine. i) Principal of operation of 4 stroke diesel engines.ii)Material used for diesel engine parts.iii)Engines various parts and their functions.iv)Process of combustion and detonation.v) Different designs of combustion chambers 1. Diesel Engine : upkeep, maintenance and repairs and overhauling decarbonizing and troubleshooting. 2. Use of gauges like vacuum gauge, compression gauge, Stroboscope and dynamometer test. 3. Valve adjustment and valve timing diagram etc. 4. Definition of horse power, Mechanical efficiency, brake, horse power, cubic capacity etc. 4. FUEL FEED AND EXHAUST SYSTEM -i) General layout of diesel fuel injection system.ii) Working of diesel fuel system parts like fuel pump, fuel filters, fuel injection pumps types or governors and their working.iii)Distributor type fuel injection pump working .iv)Fuel airlock removing.v)Injections and injectors testing. vi)Fuel feed pump parts.vii)Phasing and calibration of fuel Injection pump.viii) Replacing F. I. Pump from the Engine .ix)3Phase of Diesel fuel combustion. x)Fuel gauge.xi) Diesel as a Fuel, octane number, Air cleaner. xii) Trouble shooting and maintenance of fuel Injection system.xiii)Manifold and silencer muffler.xiv)Direct and indirect injection. 5. ENGINE COOLING SYSTEM-Necessity of Diesel Engine cooling types of Engine cooling systems Air cooling system - water cooling it's types and then working radiators construction parts in water cooling system thermostat water pump fan belt, Temperature gauge Radiator pressure cap De-aeration cooling system cooling system additives cooling system troubles and maintenance. 6. ENGINE LUBRICATION SYSTEM-Necessity of lubrication. Types of lubricants used in motor vehicle Lubricant system & types of Lubrication system Plash lubrication, force feed lubrication mist lubrication Two stroke lubrication Parts in engine lubrication system their types & functions oil fitters by pass and pressure relief valve oil pump Oil pressure gauge Oil coolers Heat exchangers Automobile lubricants types liquid, semi solid and solid lubricants S.A./E. Number, Viscosity oil used oil used in Engine, Gear box, differentials etc. additives greases, chassis lubrication various types of Bearing used in motor vehicles lubrication system troubles and maintenance. 7. AUTOMOBILE ELECTRICITY-Necessity of electrical system, Working of Auto electricity construction, operation and maintenance and storage battery, dynamo, Alternator, starter Ignition system Inverter working of regulator cut-out of solenoid system Dashboard instruments seen on instrument panel their working and maintenance, use of meter such as ohmmeter, voltmeter, megger, multimeter and it's use, H.R.D. tester, Battery charger etc. care & maintenance of auto electrical system, Electronic Ignition system. 8. TRANSMISSION SYSTEM-I)Parts of the Transmission system.II) Clutch : Principle, Construction & Operation of various types. III) Gear box : Principle, Construction & Operation of various types. IV) Propeller shaft & universal Joints : Principal, Construction & Operation of various types. V) Final drive: Principle, Construction & Operation. VI) Rear Axle & Differential : Principal, Construction & Operation of various types. 4 wheel drive operation. VII) Various adjustments in transmission system, troubleshooting & remedies in transmission system. 9. BREAK SYSTEM-I)Necessity of breaks to motor vehicle.II)Various types of brakes system & their construction & operation.III)Disc Break & Drum Breaks, Vacuum Breaks.IV) Power breaks Air pressure breaks.V)Maintenance of break system. 10. STEERING SYSTEM-I)Necessity.II) Types of steering system. Power steering concept.III) Construction, operation & Maintenance of steering system. IV) Steering geometry & wheel alignment possible faults rectification. 11. SUSPENTION SYSTEM-1) Necessity.2)Types of suspension system it's parts & functions. 3)Construction & function of stub Axle & front Axle.4)Spring & shock absorbers.5)Air suspension 6)Faults & remedies. 12. WHEELS, TYRES & CHASSIS-I)Types & parts of wheels. II)Types of tyres Tyre construction & maintenance.III)Concept of radial tyres. Tyres size.IV) Various type of chassis constructions.V)-Tyres rotation.VI) Troubleshooting of tyres, suspension and steering system. 13. PREVENTIVE MAINTENANCE


 

SCIENTIFIC INTERNATIONALTRAINING INSTITUTE

SYLLABUS OF DIPLOMA/CERTIFICATE COURSE.

CIVIL DRAUGHTSMAN [ CD ] [ CD – I / AD – I / DCES – I / ADCES – I ]

1. Introduction to Building Construction. Classification of Structure. Components of a building. 2. Introduction to Engineering material. Lime, Sand, Cement and Mortors etc. 3. Brick Masonry. Definition of brick, size of bricks, manufacturing of bricks, characteristics of good bricks. Terms used in Brick masonry, Principles of construction in Brick masonry, Bonds – English band, Flemish bond. Scaffolding, Types of Scaffolding. 4. Stone Masonry Terms used in Stone Masonry. Principles of Construction in stone masonry. Types of Stone Masonry. Comparison between Stone Masonry and Brick Masonry. 5. Foundation Definition of Foundation, Purpose of Foundation, Causes of Failure of Foundation. Formula for determining width and depth of foundation. Types of Foundation. Examination of ground, General Inspection of Soil and methods. 6. Dampness and It’s prevention Definition of Dampness, Causes of dampness. Prevention of Dampness, Material used for D.P.C. 7. Floors.Definition, Types of Floors, Construction of Different types of flooring, skirting & dado. 8. Arches and Lintels Definition of Arches, Terms used in Arches, Types of Arches. Definition of Lintels, Types of Lintels. 9. Roofs- Definition, Types of Roofs – Pitched Roof & Flat Roofs. Terms used in Roof., Types of Pitched Roofs.Types of Roof covering.Flat Roof. 10. StairsDefinition, Terms used in Stair, Types of Stairs, Requirement of good stairs.R.C.C. Definition, Material used in R.C.C.Grade of Concrete, Water cement Ratio.Working of oncrete slump Test. Formwork.Reinforament Detailing in R.C.C. work.,Structural Steel work , Types of Rivets, Advantages Rolled steel sections. Steel column, girder and beams. Connection between columns and beams. 13. Domestic Services Plumbing, Definition of Plumbing, Tools in Plumbing. Sanitary Fittings. Terms used in House plumbing, water supply system, House drainage System. 14. Units and Measurement. 15. Conversation of Units, Area & Volume (Rectangle, Square, Parallelogram, Rhombus, Triangle, Circle)

 


CIVIL DRAUGHTSMAN [ CD ] [ CD – II / AD – II / DCES – II / ADCES – II ] DRAWING PAPER SYLLABUS 1. Engineering Drawing, Introduction, Drawing is the language of Engineers, Drawing Instruments, Equipments and Materials. 2. Lettering Technique, Lines Lettering & Dimensioning, Types of lettering, lines and Dimensioning. 3. Different scales used in drawing ( Plain & Isometric ), concept of Representative factor. 4. Orthographic projection, planes of projection, First angle projection & Third angle projection. 5. Projection of lines, points & planes. Points in different quadrants, Lines parallel to one or both planes, Lines perpendicular to planes, Traces of planes, Types of planes, perpendicular and oblique planes. 6. Isometric Projection, Isometric axes, lines & planes, Isometric Projection of planes, Prisms, pyramids, To draw Isometric object from given views. 7. General Civil conventions; Meaning of F.S.I., built up area, carpet area, Rules for selecting different types of rooms & their sizes & floor heights. 8. Doors, Windows, Ventilators, Types, Parts of D / Ws, Sizes, Fixtures & fastenings used for different D / Ws, Sketches of D / W & ventilators & drawing details. 9. Plumbing accessories, types, Fitments & Sanitary symbols, plumbing symbols. 10. Electrical symbols, system of wiring, Types of wiring, layout diagrams. 11. Structural steel work drawing, Drawing of slabs, beams, columns, R.C.C., foundations, stairs. 12. R.C.C. details of Frame structures, Form work for column, beams, stairs, bar bending schedule. 13. Definitions of important terms used in building construction. 14. To prepare plan, elevation & section from line drawing for single & double storeyed Residential building drawing, Concept of site plan layout plan etc. DRAWING SHEETS : 1 Lines, Lettering, Dimensioning 2 2 Plain scales and Isometric scales 1 3 Orthographic Projection 3 4 Projection of Point and Line 2 5 Projection of Plane and Solid 2 6 Isometric Projection 3 7 R.C.C. Drawing of :1. Column Footing, 2. One way and Two way slab 3. Dog-legged Stair, 4. Lintel and Chajja 1 8 Different types of Doors and Windows 2 9 Different types of Stair and Staircases 1 10 Line Plan of Plumbing work and Sanitary & Water supply work 1 11 Symbols of Materials, Sanitary and Water supply Symbols 1 12 Electrical symbols and Wiring layouts 2 13 Structural Steel Work :1. King Roof Truss 2. Queen Roof Truss 3. lean to Roof 3 14 Complete set of Drawings for : 1. Small Office 2. Residential building 3. Residential and Double Storey building 4. Tracing of Drawings, Inking work and Ammonia Print- outs. 1 2 2 2 Total 31 Note : Student should complete 8 sheets from point no. 1 to 6. Student should complete 14 sheets from point no. 7 to


14. [AD – III / DCES – III / ADCES – III ] 1. Field Activities ? Agencies Associated in Building industry. ? Plan Sanctioning Authorities. ? Building rules and bye – laws, F.S.I., carpet area, Built – up area calculations. ? Procedure of submitting plans for approval to plan sanctioning authority. ? Planning of building. 2. R.C.C. ? Preparation of Concrete. ? Mixing and Planning concrete. ? Cutting and bending of bar, length of hooks and bends laps kept, minimum cover space etc., Bar bending schedule. 3. Domestic Services. ? Septic Tank, Soak Pit. ? Sewers and drains. ? Domestic water supply and installation of water supply system of building. 4. Surveying and Leveling. ? Brief idea of surveying and classification of Survey. ? Chain Surveying, Instruments in chain Survey, field book. ? Plane Table Surveying, instrument used, Advantages and Disadvantages of plane tabling, Methods of Plane Tabling. ? Leveling, Terms used in leveling. ? Different types of Levels, Dumpy level and leveling staff. ? Contouring, Characteristics of contours, uses of contours. 5. Estimations ? Define Estimate, Types of Estimates. ? Methods of taking out quantities. ? Units of Measurements and Payments of Common items in Civil Engineering works. 6. Finishes ? Surface Finishing, painting, varnishing, Polishing, Distempering, Cementing, Wall Papering, Plastering, Glazing work, white and colour washing.

 


DIPLOMA CIVIL ENGINEERING SERVICES ( DCES – IV ) 1. ESTIMATING & COSTING a) Introduction.b) Different methods of taking out quantities center line, out– put & in-in problems on square, Rectangular & Circular Sections. c) Units of measurement & unit of payment of different items of works. d) Calculation of quantities of materials for, i) Plain cement concrete of different proportions. ii) Brick & Stone Masonry in cement & lime mortar. iii) Plastering & Painting with Cement Mortar in foundation & Super structure. iv) Woodwork for fully paneled doors & windows. v) R.C.C. slab – Calculating Reinforcement & concrete. vi) Painting work for brick work & stone work. e) Analysis of rates of the following items of work – includes labour, material • rates etc. • Earthwork in Excavation & filling. • Cement concrete in foundation. • R.C.C. & R.B. in roof slabs. • I Class burnt brick masonry in C.M. • Coarse vabble stone masonry in C.M. • Cement Plaster. • Cement pointing – flash & deep pointing. • White washing on new surface • Painting on new woodwork. • Cement concrete floor. • Paneled & glazed door. f) Preparation of detailed estimate; complete with detailed reports, specification etc. preparation of complete estimate of proposed bungalow. g) To prepare abstract sheet from given drawing. h) Types of Contracts, Tender Notice, Documents required in Tendering conditions of contracts, adding % as contractors profit. i) Taking out quantity for septic tank. 2. CONSTRUCTION MANAGEMENT a) Introduction : Classification of construction into light, heavy & industrial. Importance of construction industry, Agencies Associated with construction works. b) Construction Planning : Necessity & Importance, Planning at different stages, methods of planning, scheduling, pretender & contract planning by contractor, types of schedules. c) Construction Labour : Introduction, Labour welfare, payment of wages act, minimum wages act. Workmen compensation act, contract labour act, labour insurance act. d) Inspection & Quality Control Introduction, stages of Inspection, Major items of control, Technical services required for inspection. e) Safety in Civil Engineering : Importance, terms used, Accident, Accident cost, safety – programme. 3. ACCOUNTa) Introduction : Necessity of maintaining accounts, List of reference books, in accounts. b) Stores & material Management : Introduction, Material management, Stores, Necessity & Safely of stores, monthly balance return of stock, surpluses & shortages of stock, Action for rectification of stock register, Losses of stock, Recording the loss, estimates of loss of stock & writing off. c) Different types of contract : % rate contract as per C.S.R. Labour rate (% above or below) for various items for covered area construction through rate basis, item rate contract. Types of Contract. d) Allotment of Works : Concept of quotation, tender, contract agreement – brief reference, work order, rules & different types of forms, Deposit works.


 

INTERIOR DESIGNING AND DECORATION [ ID ] [ID - I ] 1. history of Interior Design - 1.1 Interior decoration as a profession. 1.2 Emergence of professional interior designer. 1.3 Modern Interior design features. 2. Basic of Design Composition - 2.1 The Elements – Line, Form, Texture, Colour, Pattern, Light. 2.2 The Principles – Balance, Emphasis, Rhythm, Proportion, Unity or Harmony. 3. Introduction to building material - 3.1 one, Clay Products Cement, Mortor, Concrete, Timber, Plywood and related Products, Plywood and Related Products, Plastic and Related Products, Glass and Related Products, Paints and Related Products, Ferrous and Non-ferrous metals, Gypsum and Related Product, Adhesives. 4. Air Conditioning - 4.1 The need for Air – Conditioning. 4.2 Air – Conditioning under Indian Climatic Condition. 5. Lighting - 5.1 Different types of light arrangement. 5.2 Variety of lamps 5.3 Lighting Accessories. 5.4 Electrical Wiring. 6. Acoustics - 6.1 Properties of Sound. 6.2 Acoustic design of a hall. 6.3 Guidelines for good acoustic design. 7. Building Protection - 7.1 Dampness Protection. 7.2 Termite Protection. 7.3 Fire Protection. 8. Interior furnishing - 8.1 Ceiling – Suspended Ceiling. 8.2 Walls – Painting, Wallpaper, Panelling, Cladding, Glass, Fabrics. 8.3 Doors and Windows – Curtains, Blinds. 8.4 Flooring – Stone Flooring, Marble Flooring, Tiled Flooring etc. 8.5 Furniture – Upholstery, Partition, Built in Furniture. 8.6 Decorative Items – Plants, Flowers, Paintings, Sculptures, Pictures. 9. Painting Interiors - 9.1 Ingredients of Paint. 9.2 Types of Paints – Water – Based Paints, Oil – Based Paints. 9.3 The Painting process. 9.4 Common painting defects and remedies. 10. Quantities and Estimating - 10.1 Need of Estimating. 10.2 Method of Estimating. 11. Vastushastra - 11.1 Introduction to Vastushastra.


INTERIOR DESIGNING AND DECORATION [ ID ] [ ID - II ]

DRAWING PAPER SYLLABUS List of Sheets – 1. Study of Lines 2. Study of Scales 3. Study of Views 4. Orthographic Projection of a cube 5. Orthographic Projection of an oblong 6. Iso and Ortho of a dressing table. 7. Iso and Ortho of a chair. 8. Iso and Ortho of a wardrobe 9. Various Types of Materials 10. Sitting Arrangement 11. Colour Schemes 12. Residential Drawing in British and Metric Scale – A) Plan B) Elevation 13. Designing Furniture in Living Room. A) Plan B) Elevation C) Section 14. Designing Furniture in Kitchen A) Plan B) Elevation C) Section 15. Designing furniture in bed Room A) Plan B) Elevation C) Section 16. Commercial Drawing – shops 17. Different types of board 18. Different types of bats of bricks 19. Different types of Carpentry joints. 20. Details of Doors and Windows 21. Construction of Kitchen Platform 22. Shades and Shadows 23. Colour Wheels 24. Different types of accessories 25. Designing dressing table 26. Different types of table lamps 27. Different types of plants 28. Different types of curtains 29. One Point perspective – A) Bed Room B ] Kitchen C ] Living Room 30. Two Point perspective – A) Bed Room B ] Kitchen C ] Living Room


DIGITAL ELECTRONICS & MICROPROCESSOR [ DEM ] DEM / DCHES - I / DCNES – I ]

1.A) BASIC ELECTRONICS: -a) Concept of open & short circuit. b)Ohm’s law, current, voltage & Resistance relation, Power unit Power consumption. c)Soldering & de-soldering Technique. B) ELECTRONIC COMPONENTS: - Resistor, capacitor, inductor, Transformer. 1) Types 2) Values (by colour code, Number system) 3) Testing 4) Use’s C) SEMICONDUCTOR: - a) Electric properties of conductor, Semi-conductor & Insulator. b) Definition of Semi-conductor. Suitable material for formation of P-Type & N-Type Semi-conductor. Impurities of P-Type & N-Type material. c) Diode Junction Diode, Zener Diode, Light Emitted Diode, photo Diode 1) Types 2) Number System 3) Testing 4) Uses. d) Transistor Types: -NPN & PNP ,Germanium & Silicon. Testing of Transistor using Multimeter. e) Integrated circuit (IC’s) Introduction, Types of IC’s, Merit & De-merit of IC’s. 2) BASIC OF TRANSISTOR CIRCUIT: - a) Biasing of Transistor. Fixed bias, Potential divider bias, Self bias. What is Thermal run-away of transistor and what is the solution on it? b) Class of Amplifier: - Basic circuit of class –A, class-B, class-C Amplifier. c) Configuration of transistor: - Common base amplifier, common Emitter amplifier, Common collector Amplifier. Definition of Alpha ??& Beta. d) Study of Single Stage amplifier. e) Types of coupling R-C, L-C, Transformer & Direct coupling circuit. Merit & De-merit of it. 3) DIGITAL ELECTRONICS: - a) Different number system, Study of different codes,Study of Logical Gates,Binary adder & sub tractor, Demorgan’s law. b) Study of FLIP-FLOP : SR, JK, MS-JK, D, SR-T. c) Counter : Binary, BCD, Mod-Nth, UP and Down, Ring counter. d) Registers : Serial and parallel registers. ( Right/Left) e) A/D and D/A Converters: Basic D/A converter, Ladder and Weighted type. Basic A/D converter, SAR, Counter ramp type. f) Combination network using Gates: Encoder, Decoder, Parity encoder, Parity generator. Multiplexer, De-Multiplexer. g) Semiconductor Memory : RAM, ROM, PROM, EPROM, EEPROM, Static and dynamic memory & flesh memory 4. MICROPROSESSOR- a) Introduction to 8085 Microprocessor, Block diagram of 8085 Microprocessor. b) 8085 Microprocessors system organization & its Terminology. c) Block diagram of 8085 kit., Study & Interfacing of µp kit (keyboard, LED, LCD, seven segment display) d) With reference to 8085 microprocessor, study the following interfacing IC’s : 8150, 8251, 8253, 8259, 8279, 74244, 74245. e) Programming in 8085 kit. 1) Flow charts. 2) 8085 Instruction set. 3) Simple programmed as per the given practical list. 5) SWITCH MODE POWER SUPPLY (SMPS): -a)Basic principal of SMPS. b)Block diagram of AT SMPS & AT-X SMPS.c)Colour code of wires, different voltages and current outputs.d)Introduction to UPS, Block diagram, Installation. 6) KEYBOARD AND MOUSE: - Type’s of Keyboard’s c)Testing of Keyboard using KBD utility.d) Types of Mouse and his internal physical layout.e)Interconnection of PC-5pin keyboard socket, PS-2 keyboard, 9/15 pin Serial Mouse, PS-2 Mouse. 7) ELECTRONIC DISPLAY: -Seven Segment LED / LCD Display, Gas discharge display. 8) TEST INSTRUMENTS: -Application & use of Oscilloscope, DMM, Frequency meter, logic probe, Logic analyzer, Block diagram of Digital voltmeter, Digital frequency meter, Digital clock.

 


SCIENTIFIC INTERNATIONALTRAINING INSTITUTE SYLLABUS OF DIPLOMA/CERTIFICATE COURSE-

ELECTRONICS. COMPUTER MAINTENANCE [ CM ] [ CM / DCHES – II /DCNES – II ]

1) IBM PC – SYSTEM a) Block diagram of PC_ System. Different Input and Output devises. b) Physical layout of Mother board (Socket-7, Slot-1 and Dual ) c) Different CPU (P-I, P-II, P-III and P-IV) advantages and disadvantages. d) Study of RAM used in PC. e) Different connectors, Cables and Sockets use in system. f) Study of C-MOS (Award/AMI bios) 2) F.D.D. & H.D.D. a) Study of FDD and HDD drive (Types Capacity, Size, etc.) b) Physical installation on FDD and HDD. c) Jumper Setting of HDD, Twisted cable of FDD. d) Formatting of Floppy disk. e) Partitioning and formatting of Hard disk. f) Study of different Interface (IDE, ATA, WATA, ATAPI, etc.) 3) MONITOR (VIDEO DISPLAY UNIT) a) Study of different video display (monitor/LCD) b) Block diagram of mono VGA monitor/ Colour VGA monitor. c) Study of different display adopter cards. d) Study of Resolution and its setting. e) Installation of Display adopter. 4) SYSTEM SOFTWARE & DIAGNOSTIC TOOLS a) Installation of Window. (Win 95/98) b) Study of Internal and External DOS Commands ( Dir, Drive select, Check disk, CD, MD, RD, Copy, Fdisk, Format, Disk copy, Scandisk, Ver., Time, Date, etc.) c) Study of Viruses and antidotes : Norton, PC-Cline, etc. d) Study of Window (Control Panel, System Tools, Device manager, Display properties) e) Introduction for use of Advances diagnostics (DM, Partition Magic, Defragmentation, etc.) f) Study of Internet (To open E-mail account, Send and receive the E-mail) 5) CD R/W AND MODEM a) Study of CD-ROM and installation under DOS. b) Installation of CD-W under windows. c) Study of Modem (Internal and External). d) Installation of Modem. e) Inter connection of CD-R/W, DVD, External Modem and PC- System. f) Installation of DVD. 6) DIFFERENT ADON CARDS (Sound, TV Tuner, Network, DVD, Web. camera, etc.) a) Installation of Sound card drivers. b) Installation of TV Tuner card. c) Installation of Network Adopter. d) Installation of Web Camera. 7) PRINTER a) Types of Printer (DOT matrix, Inject, Laser Printer). b) Interconnection of PC and Printer. c) Installation of Printer in Window and DOS. d) Study of Printer sharing switch. 8) SCANNER a) Types of scanner. b) Study of Block diagram of scanner. c) Study of Installation of scanner 9) DIGNOSTIC a) Preventive Maintenance. b) Booting Problems. c) FDD/HDD Problems. d) Keyboard / Mouse Problems e) Printer Problems.

 


SCIENTIFIC INTERNATIONALTRAINING INSTITUTE

COMPUTER NETWORKING [ CCN ] [ CCN / DCNES – III ]

1) REVISION OF SYSTEM SOFTWARE & DIAGNOSTIC TOOLS: - a) Installation of Window. (Win 95/98/98SE) b) Study of Internal and External DOS Commands ( Dir, Drive select, Check disk, CD, MD, RD, Copy, Fdisk, Format, Disk copy, Scandisk, Ver., Time, Date, etc.) c) Study of Viruses and antidotes : Norton, PC-Clint, etc. d) Study of Window (Control Panel, System Tools, Device manager, Display properties) e) Introduction for use of Advances diagnostics ( DM, Partition Magic, Defragmentation, etc.) f) Study of Internet (To open E-mail account, Send and receive the E-mail) 2) NETWORKING BASICS: - a) Networking : Introduction ,Topology ,Network components. b) Network Media: UTP, STP, Coaxial cable, Optical Fiber . c) Protocols –Definition, Types (TCP/IP PROTOCOL- advantages, Addressing ) d) Network Architecture : Ethernet, Token Ring, Apple Talk, Arcent . e) Network Access Methods. f) Concept of OSI Model 3) NETWORK ENVIRONMENT: - a) Network Operation : Server , NOS, Workstation ,Services , Applications . b) E-Mail Standards. c) Client/Server Environment. d) Network Management. e) Workgroup Environment. f) Network Data Security – Password, Access Control, Data Encryption , g) Audition, Virus Protection, Back Up. h) Data Transfers Modem, PSTN, Leased lines, ISDN . i) Repeaters, Bridges, Routers, Brouters (Introduction). j) Router Protols. Gateways. WAN Types. 4) LINUX: - a) Linux installation – Server & Workstation. b) Configuration & Operation of Linux Workstation. c) Basic Linux commands. 5) A) INTRODUCTION TO WINDOWS XP, NETWORK OPERATING SYSTEM (NOS) & NOVEL NETWORK B) WINDOW 2000 SERVER & WORKSTATION: - a) Installation of Window 2000 Server . b) Installation of Window 2000 Workstation. c) Configuration of Window 200 Environment. d) Window 2000 Administration. e) Application Support. f) Remote Access Service . g) Configuring TCP/IP network Services. C) INTRODUCTION TO 2003 (DIFFERENCE BETWEEN WINDOWS2000 & 2003). 6) WEB TECHNOLOGY: - a) Installation of Web Server ( Microsoft PIS 4.0 Server ) b) Installation of E-Mail & Internet Services. c) Installation of net version software e.g. Office 2000, CAD, Photoshop etc. d) Implementing Microsoft W.W.W. (World Wide Web ) services (IIS) e) Implementing & installing Internet Services f) Implementing FTP , SMTP , SNTP ,Security Features for Web server. g) Indexing Web sites using Microsoft site Server Express. 7) DIAGNOSTIC: -Study of network Debugging Tools , E-Mail , Internet , GOPHER ,WWW, FTP services. Debugging in window 2000. Debugging in Network Printer.


SCIENTIFIC INTERNATIONALTRAINING INSTITUTE

SYLLABUS OF DIPLOMA/CERTIFICATE COURSE-

COMPUTER ACCOUNTING TALLY - (ACT) ACT / DCAM – I / DCA – II ]

1) Fundamental of Accounting Concept of Manual Accounting & Computerized Accounting, Features of Tally, Grouping in Tally, Company Creation, Alteration, Selection, Understanding Tally Screen, Chart of Accounts in Tally. 2) Features of Tally Accounting with Pre-defined Group in Tally, Opening Balances, Creating, and Managing & Altering of Ledgers. 3) Accounting Voucher Introduction to Accounting Voucher, Predefined Vouchers type, Create a new vouchers type, Different types of Vouchers, Making Entry in Voucher Mode, Rules for making Entry in Voucher Mode. 4) Inventory Master Introduction to Inventory Masters, Stock Items, Stock Groups, Creating Units, Stock Categories, and Maintain Stock Categories, Maintain batch-wise details, Set expiry date & Manufacturing date for batches, Maintain Multiple Location. Inventory voucher Introduction to Inventory Voucher, Predefined Vouchers type, Create a new vouchers type, Different types of Vouchers, Making Entry in Voucher Mode, Rules for making Entry in Voucher Mode, Order Processing System Stock Journal, Physical Stock. Invoicing Introduction, Working with Invoicing, Configuring the invoice, Working with invoicing entry, Sales Voucher number, Delivery Note, Inventory allocations, Accounting details, Bill details, Printing invoice and vouchers. 5) Bank Reconciliation Statement- Introduction to Bank Reconciliation, Working with Bank Reconciliation, Reconciliation of Bank Book. Interest calculation Introduction, Simple Mode, Interest calculations on outstanding balances, Interest calculations transactions by transactions, Using Voucher class for Interest calculation. 6) Report Viewing and Understanding reports in Tally, Exploring Balance Sheet, Profit & Loss A/c, Trial Balance, And etc… [ C. TAX / DC.Tax & BM – I ] 1) TAX ADMINISTRATION Advance entries in Accounting Master, Configuration of Tally, Bill-wise details, Activating F11 Features. Additional cost on Purchase, Multiple Godown. Entries in Invoice Mode, accounting allocation, Inventory allocation. Central Sale tax entries, Vat, Vat From, TDS Form, Tax on Services and Tax Challan. Entries with discount column, Zero Value Entries in voucher. Introduction to Tax Structure in India, Direct & Indirect Tax. Orientation to Income Tax, Provision of Income Tax, Heads of Income, Forms & Return, and Tax Deducted at Source, Exemptions, Orientation to Sales Tax, and Orientation to Central Excise ACT. Provisions of Income Tax, Form & Returns of S.T., Schedules of Goods, Liability & Rate of Tax, Drawback & Set off, Tax Management & Planning. Computerized Forms of Tax. Single Point Levy of Tax, Turnover Tax on Schedule ‘C’ Goods, Tax at Reduced Rate, No deduction from turnover Except on Declarations, Purchase Tax on Purchase, Surcharge Drawback, set-off, Refund Etc, Computation of Turnover & Tax, Introduction, Excise V/s Sales Tax, Scope of BST Act, Definitions, Incidence of Tax, Tax Liability, Tax-free Goods, Declared Goods, Applicability of the law, Tax Structure. Important Definitions, Principals of Determining Interstate Sales & Purchase, Liability of tax, Rate of Tax


SCIENTIFIC INTERNATIONALTRAINING INSTITUTE

SYLLABUS OF DIPLOMA/CERTIFICATE COURSE- COMPUTER. MS-OFFICE

1) Computer Fundamentals What is a Computer, Features of Computers, Other Peripherals, Types of Memory, Internal Storage, External Storage Computer system, Input and Output Devices, Keyboard familiarity Switching ON a computer, Shutting Down a computer, Essential care to be taken while working on a computer. Hardware, Disks, Hard disk, Floppy Disk, CD ROM, Software, Types of software, System software, Application Software, Utility Operating System, Bits & Bytes, Central Processing Unit. 2) Windows Getting started with windows, Introduction to windows, Desktop, Icons, My computer, Date/time Display, Background, Screen Saver, Taskbar, Finding files, Help, Run. 3) Word Pad Working with documents, Working with Text, Formatting Text, Printing a document. 4) Paint Introduction to paint screen and toolbox, Drawing lines and shapes, Working with color, Erasing, Working with part of a picture, Changing how your Picture looks on screen. 5) Windows Explorer Creating a folder, Changing the name of a file or folder, Copying a file or folder, Moving a file o folder, Deleting a file or folder, Retrieving deleted files 6) Ms-Word Introduction to word screen, Starting a new document, Entering text, File menu, New, Open, close, save, save as, print preview, page setup, print, Edit Menu, Undo, redo, cut, copy, paste, clear, select all, Find, replace, goto. View Menu, Normal, print layout, Toolbars, Header & footer, Full screen, zoom, Insert menu, Break, Page numbers, date & time, Autotext, symbol, footnote, Picture, Text boxes, File, Bookmark, Hyperlink. Format menu, Font, Paragraph, Bullets & Numbering, Borders and Shading, Columns, tabs, drop Cap, Change case, background, Tools Menu, Spelling & Grammar, Language, word count, Autocorrect, Mail Merge, Envelopes and labels, Table menu & Window Menu. 7) Ms-Excel Introduction to Excel screen, Creating a new workbook, Entering data, Moving or copy characters within a cell Copy only values, comments, or cell formats, Exiting excel. Automatically filling data, Fill in a series of numbers, Fill in a series from a formula, Select blank cells, Select cells that contain comments Editing cell contents, Clear contents, format or comments from cells Delete cells, rows or columns, Undo mistakes, Find text or numbers, Insert blank cells, columns and rows. Enter a formula, Enter a formula that contains a function Calculation operators in formulas, Comparison Operators, Switch to another sheet in a workbook, Select sheets in a workbook, Inserting a new worksheet, Moving and copying sheets. Format text, Copy formats from one cell or range to another, Change the text color, Make selected text or numbers bold, italic, or underlined, Apply borders to cells, Shade cells with solid colors, Shade cells with solid patterns, Remove borders Remove shading, Add background patterns to an entire sheet, Remove a sheet background pattern, Conditional formatting, Align data at top, center, bottom of cell. Creating a chart, Delete a data series, labels Change data series names or legend text, Select a different chart type. Spelling, Autocorrect, Goal seek, Scenarios, Auditing. Sorting rows in ascending/descending order Sort rows based on contents of two or more columns, Tables, Goal seek, Filters, Create custom headers and footers. 8) Ms-Powerpoint Introduction to PowerPoint window, Features, How is PowerPoint, Useful, Slides, Handouts and Speaker notes, Creating a Presentation using AutoContent Wizard, Viewing your Presentation, Editing your Presentation Outline, Saving the presentation. Creating Blank Presentation, Types of Auto Layouts, Opening an existing presentation, Checking Spelling, Deleting slides, Moving Slides, Inserting a slides. Slide Master, Working with Header and Footer, Drawing Toolbar, Changing Font and Font Size, Inserting a picture, Applying, Background Color, and Inserting Slides from file. Rehearse Timings, Adding, and Slide Set up Show, Custom Animation Effect. 9) Internet Concept of WWW, Internet Surfing & E-Mailing.


INFORMATION TECHNOLOGY ( I T ) [ CCIT / DCA – II / DCP & SA – I ].

1) Computer Fundamentals -What is a Computer, Features of Computers, Uses, Types of Computers, History of Computers, Generation of computers, Other Peripherals, Types of Memory, Internal Storage, External Storage Computer system, Input and Output Devices, Keyboard familiarity Switching ON a computer, Shutting Down a computer, Essential care to be taken while working on a computer.Hardware, Disks, Hard disk, Floppy Disk, CD ROM, Software, Types of software, System software, Application Software, Utility Operating System, Languages, Compilers & Interpreters, Bits & Bytes, Central Processing Unit, What is Virus, Types of Viruses, Methods of Eliminating Viruses. 2) Windows-Getting started with windows, Introduction to windows, Desktop, Icons, My computer, Network neighborhood, Recycle bin, Notepad, Settings - Control Panel, Date/time Display, Background, Screen Saver, Appearance, Mouse, Printers, Adding a printer, Taskbar, Adding and removing programs, Find, Finding files, Help, Run. 3) Word Pad-Working with documents, Working with Text, Formatting Text, Printing a document. 4) Paint-Introduction to paint screen and toolbox, Drawing lines and shapes, Working with color, Erasing, Working with part of a picture, Changing how your Picture looks on screen. 5) Windows Explorer-Creating a folder, Changing the name of a file or folder, Copying a file or folder, Moving a file o folder, Deleting a file or folder, Retrieving deleted files 6) Networking Concept – I-What is networking, Types of networks, Required Network elements. Concept & Definition of Network services, Transmission media, File services, Print services, Application services, Message services, Database services, Communication media, Types of transmission media, Cables. Topology, Types of Topologies, Types of hubs, Network Connectivity, Repeaters, Types of repeaters, Bridges, Routers, Gateways, Network Interface card (NIC), Modem, Protocols 7) Ms-Word -Introduction to word screen, Starting a new document, Entering text, File menu, New, Open, close, save, save as, print preview, page setup, print, Edit Menu, Undo, redo, cut, copy, paste, clear, select all, Find, replace, goto. View Menu, Normal, print layout, Toolbars, Header & footer, comments, Full screen, zoom, Insert menu, Break, Page numbers, date & time, Autotext, symbol, comment, footnote, caption, Picture, Text boxes, File, Object, Bookmark, Hyperlink. Format menu, Font, Paragraph, Bullets & Numbering, Borders and Shading, Columns, tabs, drop Cap, Change case, background, style, Tools Menu, Spelling & Grammar, Language, word count, Autocorrect, track changes, merge, documents, Protect Document, Mail Merge, Envelopes and labels, Table menu & Window Menu. 8) Ms-Excel -Introduction to Excel screen, Moving around, Creating a new workbook, Entering data, Moving or copy characters within a cell Copy only values, comments, or cell formats, Copy only visible cells Using Transpose, Exiting excel. Automatically filling data, Fill in a series of numbers, Creating a custom fill series, Change or delete a custom fill series, Fill in a series from a formula, Select blank cells, Select cells that contain comments Editing cell contents, Clear contents, format or comments from cells Delete cells, rows or columns, Undo mistakes, Repeat last action, Find text or numbers, Insert blank cells, columns and rows. Increase or Decrease no. of decimal places, Add or remove a currency symbol, Enter a formula, Enter a formula that contains a function Calculation operators in formulas, Comparison Operators, Switch to another sheet in a workbook, Select sheets in a workbook, Inserting a new worksheet, Moving and copying sheets. Format text and individual characters, Copy formats from one cell or range to another, Change the font or font size, Shrink the font size to show all data in a cell, Change the text color, Make selected text or numbers bold, italic, or underlined, Apply borders to cells, Shade cells with solid colors, Shade cells with solid patterns, Remove borders Remove shading, Add background patterns to an entire sheet, Remove a sheet background pattern, Conditional formatting, Align data at top, center, bottom of cell, Rotate text in a cell. Creating a chart, Change cell range used to create a chart, Change values in a chart, Delete a data series, Change category axis labels Change data series names or legend text, Select a different chart type. Spelling, Autocorrect, Share workbook, Track changes, Merge workbook, Protection, Goal seek, Scenarios, Auditing. Sorting rows in ascending/descending order Sort rows based on contents of two or more columns, Tables, Goal seek, Pivot table, Filters, Advanced filters, Create custom headers and footers. 9) Ms-Powerpoint Introduction to PowerPoint window, Features, How is PowerPoint, Useful, Slides, Handouts and Speaker notes, Creating a Presentation using AutoContent Wizard, Viewing your Presentation, Editing your Presentation Outline, Saving the presentation.Creating Blank Presentation, Types of Auto Layouts, Opening an existing presentation, Checking Spelling, Deleting slides, Moving Slides, Inserting a slides.Slide Master, Working with Header and Footer, Drawing Toolbar, Changing Font and Font Size, Inserting a picture, Applying, Background Color, and Inserting Slides from file. Rehearse Timings, Adding, and Slide Set up Show, Custom Animation Effect. 10) Internet Concept of WWW, Internet Surfing & E-Mailing.


D.T.P.

1) PageMaker – Process Overview, Environment, Toolbox, Dialog Box, Working with Ruler & Guides, Additional Help Resources, Working with Text, Text option, Using Story Editor, Printing. Layout Solutions Working with Leading, Advance Character Formatting, Insertion & Removing Pages, Working with Columns, Graphics: An Overview, Drawing with PageMaker, Working with Graphics, Getting started with Colors, Cr\eating Color Library.Pagemaker Styles, Using Master Pages, Using Master Pages, Using PageMaker Templates, Working with the Add Continued Line, Balancing Columns, Applying Case of Text, Working with the Drop Cap, Using the Grid Manager, Using the Build Booklet Plug-In, Using Running Header & Footers, Header & Footer 2) Introduction To Coreldraw Objects. Vs. Bitmaps, Corel Interface, Corel draw Controls, Working with Menus & Toolbars, Using Zoom & Pan Tools, Working With Dockers & Getting Help.Star-Up & File Handling. Launching CorelDraw, Creating new Document, Opening Document, Importing Graphics & Text, Saving Drawing, Making Backup Files, Exporting Drawings. Select, Move, Copy & Size. Selecting Objects, Moving, Copying, Resizing & Deleting Objects. Complex Shape. Polygon and Stars, Creating Spirals, Drawing Grids and Drawing Perfect Shapes.Nodes & Paths Three Types of Nodes, Converting an Object to Curves and Working with Nodes. 3) Line & Curves-Using the Freehand Tool, Benzar Tool, Setting the Line Properties, Adding Arrowhead, Calligraphic Lines, Cutting Object Apart , Using Eraser Tool and Artistic Media Tool. 4) Page & Document Setup-Page Size & Orientation, Background Setting, Adding & Deleting Pages, Document Navigation and Viewing Document 5) Tools For Precision-Working with the Rulers, Setting the Unit of Measures, Using Guidelines & Grid, Using Status Bar and Aligning Object. 6) Color And Fills-Solid Color Fills and Outline, Using Color Palettes, Using Eyedropper and Paint bucket, Color Management, Creating Fountain Fills, Adding Pattern to Objects, Adding a Textures Fill & Interactive Mesh Fill Tool. 7) Working With Text-Adding Text to a document, Formatting Text, Importing text, Text layout, Embellishing Text. 8) Text Special Effects-Skewing and Rotating Text, Creating Drop Shadows, Fitting Text to Path, Extruding Text and The Neon Effects. 9) Stacking & Layers-Changing the Staking Order and Working with Layers 10) Object Arrangement-Grouping Objects, Locking Objects, Combining & Breaking Objects Apart, Transforming Object and Shaping Objects. 11) Special Effects-Using Envelops, Blends, Adding Perspective, Creating Shadow Objects, The Power clip Command, Interactive Transparency Tool, Interactive Distortion Tool, Interactive, Contour Tool and Lens Docker. 12) Symbols, Clip Art & Bitmaps Working with Symbols, Using the Scrapbook Dockers, Working with Bitmap Images, Acquiring Images. 13) Printing-Basic Printing, Printing Oversized Drawings, Alternate Printer Paper Options, Using a Service Bureau, Preflight and Print Preview, Creating PDF File. 14) Introduction To Photoshop-Getting Familiar with the Welcome Window, Introducing the Work Area, Working with Palettes, A Closer Look at the Image Window, Navigating Menu Commands. 15) Customizing Adobe Photoshop Elements-Adjusting Color-Management Settings, Choosing Setting in the Preset Manager, Personalizing Your Preferences. 16) Acquiring Images From Scanner And Digital Cameras-Installing Plug-In Files, Adjusting Scanner Settings, Scanning Different Kinds of Images, Scanning the Final Image, Accessing Images on the Camera Saving Images. 17) Creating, Opening & Converting-Creating a New Document, Document Setting for Print, Document Setting for Web Images, Opening and Browsing Image Files and Converting Image Information. 18) Printing Images-Printing Digital Images, Consideration for Printing Images with Text, Improving Printer Output. 19) Photoshop Elements & Color-Color Theory, Computers and Color, Color and Photoshop Elements, Photoshop Elements Color Correction Tools, Color and Composite Images. 20) Tonal range and color correction. Introducing Selection Tools, Correcting Tonal Range, Using the Histogram with Tonal Range Tools, Changing Colors with Color Effect Tools, Replacing Colors, Introducing Color-Correction Tools, and Color-Correction Variations. 21) Applying Filter And Effects-Previewing Filters and Effects, Introducing Blur Filters, Introducing Filter Effects with Toolbox Tools, Variation with Blur Filters, Applying Artistic Filter, Exploring Effectcs. 22) Working With Layers & Layer Style-Introducing the Layers Palette, Introducing Fill Layers, Introducing Adjustment Layers, Correcting Images with Layers, Merging Layers. 23) Adding Text & Shapes -Introducing the Type Tool, Adding Graphics to an Image, Drawing and Painting Tools, Creating Transparent Text, Modifying Custom Shapes. 24) Repairing Images-Repairing Folds and Tears, Fine-Tuning the Image, Rebuilding a Damaged Photo.

 


FASHION DESIGNING [ FD ] .

1] Description of Fashion a] Indian Fashion b] Western Fashion, Effect of Society 2] Information of suitable fashion for particular personality a] Colour b] Texture c] Print 3] Types of Garments Causwal Dress, Semi- Formal Dress, Formal Dress, Party Dress 4] Different types of neck lines, colour sleeves, Skirts. 5] Different types of blouse 6] Dress Decoration a] Fabric Painting b] Smocking c] Advance Hand embroidery 7] Advance Garments Making Fancy Frock - 2 Punjabi Suit - 2 Party Dress - 2 Blouse - 20 8] Fashion Accessories A] Hat, b] Jacket c] B] Dulhan Set, Saree Cover.,Blouse Cover, Make up Kit, Shoe Cover,General Kit 9] Colour Scheme Primary, Secondary Complimentary, Split complimentary, Anolougs. 10] Collection of Paper Cutting & Dress materials. 11] We keep the " dress Exhibition in last months of course TAILORING [ TL ] 1. Introduction: Introduction to sewing machine & their parts Introduction of Stitching materials Measurement tape, Tailors Chalk, Cutting Table Fresh Curve, Scale Trangle Scissor, Needle &Thread 2. Introduction to basic stitching: 1] Types of stitching 2] Permanent Stitch (Machine Stitch) 3] Temporary Stitch (Hand Stitch) 3. Temporary Stitch.: 1) Simple, 2) Running, 3) Back Stitch, 4) Hemming, 5) Button hole stitch. Method of sewing button Hock, eye Permanent stitch (seems) Plain Seem, 2) French Seem, 3) Top Seem, 4) Piped Seem 4. Types of Tucks: 1] Pin Tucks, 2] Cross Tucks, 3] Grauded Tucks, 4] Releases Tucks 5. Types of darts: One point dart, Fish Dart 6. Different types of pleats: 1] Side pleats, 2] Box pleats, 3] inverted box pleats, 4] knife pleats. 7. Different type of opening:a] Back opening, 2] Shoulder opening, 3] Front opening


BEAUTICIAN [ BUT ]

1. MAKE UP • BRIDAL MAKE UP • NIGHT MAKE UP • DAY MAKE UP 2. FACIAL • PLAIN FACIAL • HERBAL FACIAL • ELECTRIC FACIAL • SHAHNAZ FACE PACK-PROCESS 3. BLEACHING • CREAM BLEACHING • POWDER BLEACHING 4. MASSAGE • FACE MASSAGE • BODY MASSAGE • SHAHNAZ MASSAGE CREAM 5. HAIR TREATMENT & DYE • HERBAL HAIR TREATMENT • HAIR TO IMPROVE BEAUTY • HAIR PROBLEM SOLVING • PRECAUTION TO IMPROVE HAIR STRONG • HENNA DYE PROCESS • PROCESS OF DYE 6. SKING CARE • PRECAUTION, ADVICE & TREATMENT 7. THREADING 8. WAXING • FACE WAX • HAND WAX 9. PUMMING 10. PERNING 11. YOGA • PRANAM MUDRASAN • SURYA NAMASKAR 12. MISCELLENEOUS • IMPROVE BEAUTY THROUGH MILK • IMPROVE BEAUTY THROUGH FRUITS & VEGETABLES • SIMPLE PRECAUTION BEAUTY • BEAUTY ADVICE 1)PAINTING 1. Introduction, 2. Objects of Painting 3. Types of Painting works. 2) TOOLS AND EQUIPMENTS REQUIRED 1. Brushes and its types. 2. Knife and its types.3. Scrapers.4. Rollers5. Ladders 3) PUTTY :a) Meaning and its types used for different surfaces. 4) PAINTS AND IT'S 4)APPLICATION PROCEDURE :1. Distempering 2. Varnishing and Polishing 3. Plastic paint 4. Velvette paint 5. Enamel paints 6. Cement paint7. White washing 8. Colour washing 9. Oil paint 10. Aluminium paint 5) METAL : 1. Ferrous metals definition 2. Types steel, cast iron, wrought iron 6) TOOLS AND EQUIPMENTS REQUIRED FOR PAINTING ON METAL SURFACES : 1. Brushes, 2. Scrapers, 3. Blow lamp, 4. Ladders 5. Knifes 7) PAINTING ON METAL SURFACES : 1. Detail procedure 8) ART LETTERING : 1. Types, 2. Colour combination, 3. Various sizes and styles in English, Hindi and Marathi, 9)different types of brushes and instruments required for writing art lettering work. 10) spray painting work and application procedure with tools and equipments required. 11) screen printing work and its methods. 12) writing advertising boards of different sizes. 13) stencils its cutting works and precaution taken. 14) fire and fire protection methods, storage methods 15) figure painting 16) powder coating : itsconcept and procedure. 17) mode of measurement and preparation estimate for painting works for walls, metal & wooden surfaces and art lettering .


MONTESSORI TEACHERS TRAINING [ MTT ]

1. Importance of early childhood Education. 2. Psychology of Child learning. 3. School is a place of learning. Care and useful for child. 4. Role of teacher's quality. 1. role of homes society and community in the development of the child. Interaction between parents and teachers. 2. Development of creativity, art, poetry, Equipment for numerical and geometrical, reading, writing. 3. Introduction of Environment. 1. child Psychology. 2. Methodology of Child Education. 3. Health of Nutrition of Child. 4. Child Welfare & Social Education. 5. Principal of Child Education & School Management. 6. Age-3.5 and above. 7. Are / Surrounding. PRACTICALS 1. Prayers. 2. Strokes. 3. Handicraft and Drawing. 4. Physical Education lesson. 5. Music & Cultural Programmer.6. Creation of Education Aids. 7. Nutrition. 8. Exercise through Material. 9. Child Observation. 10. Class Conduct. 11. Charts of Fruits, Vegetables, Animals. 12. Story.13. Alphabets & Number. 14. Flash Cards. 15. Computers. 16. Charts of Birds, Vehicles. 17. Poems, Songs with Action. 18. Nature Study. 19. Cries of Animals. 20. What the Baby Animals Called. 21. Colors / Shapes. 22. Conversation of My Self, Teacher, Family etc. 23. Good Habits. 24. Puzzles. 25. Beads


SEND EMAIL

e-ADMISSION

CONTACT US